Wooden Box With Drawer Plans

Download Commodity

Download Commodity

Wooden boxes are a popular project for beginning woodworkers, and making one will teach yous many bones techniques that you lot can apply to other projects. Y'all can construct your box to be uncomplicated and elegant, utilitarian, or highly stylized and busy. However you choose to design your box, it'south easiest to start out with either a hinged or sliding lid and then you tin can get some exercise before moving onto more advanced techniques.

  1. 1

    Choose your wood. You tin use repurposed forest from previous projects, boards from broken down pallets, or you tin purchase and cutting new wood. Consider what your box will exist used for.

    • For example, if you're making a jewelry box, consider thin pieces of cedar, ash or oak.[1] It will be easier to make a smaller box with thinner wood. Salvage larger pieces or boards for bigger boxes. This will also prevent you from having to practise too much trimming.
  2. two

    Assemble your supplies. Proceed all your basic tools in your workspace. If using power tools, brand certain that you have access to power outlets. At the very least, you lot'll desire a ruler, hammer, nails, forest glue or putty, and of form, your boards.

    • If using power tools, use circumspection and always wear eye protection.

    Advertisement

  3. 3

    Mensurate and mark your boards. Starting time, you'll demand to decide on the size of your box. Specifically, you'll want to determine how long, wide, and alpine to make your box. Then, mark the measurements on your boards using a ruler and pencil.

    • If you're building a box for a specific purpose or to concur a certain item, measure the item to ensure it will fit within your finished box.[2]
  4. 4

    Cut your boards, if not already to size. Employ a hand or round saw to cut the boards according to your measurements. Retrieve you lot'll need iv boards for the sides, ane for the base of operations, and one for your lid.

    • Ability tools can make the job easier, but are not necessary. Yous can easily make your box using a screwdriver, carpenter's square, hand saw, and hammer.
  5. 5

    Gather the side pieces using a butt articulation. Join the sides together at a right angle using mucilage betwixt the joints for immovability. At this indicate, it should wait like a foursquare with no base or lid fastened yet. Next, hammer or drill in finishing nails, wood screws or dowels.[three]

    • You may want to use clamps to hold the glued sides together while you drill nails or screws into them.[4]
    • If you're using dowels, drill a pigsty through the side of one piece into the side of another. Use a wooden dowel to pivot the pieces together in an "L" shape. Later the sides are pinned, cut the dowel flush with the sides.
  6. half-dozen

    Attach the sides to the base of operations. Make sure the sides sit evenly on the base or are snug around the base, depending on your design. Use glue to attach the base of operations and sides. Hammer or drill in finishing nails, forest screws, or dowels.

    • Permit your box to dry out thoroughly earlier sealing or using it.
  7. 7

    Attach a hinged lid to the box. Prepare the hat on the box so the lid and side are flush, so measure and mark where you'd similar your hinges to exist. Keep the swivel knuckle facing out from the dorsum of your box and drill or hammer to attach it to the side and then the hat.

    • When laying out the hinges, it is important that you square them to the meridian and to the sides of the case. Otherwise, the door will not shut or open correctly.
    • It's helpful to clench the side and lid together when measuring and installing the hinges.[5]
  8. 8

    Make full any smash holes. Apply a forest putty and putty knife to fill boom holes. Let the putty dry out completely before sanding the areas smooth.

    • Filling and sanding smash holes will add a professional look to your projection. Feel complimentary to omit this step if you're not concerned with decorative aspects.
  9. Advert

  1. 1

    Cull your wood. You can utilise repurposed forest from previous projects, boards from broken downwardly pallets, or yous can buy and cut new wood. Consider what your box will exist used for.

    • For instance, if you're making a jewelry box, consider thin pieces of cedar, ash or oak.[6] It volition exist easier to make a smaller box with thinner woods. Save larger pieces or boards for bigger boxes. This volition also prevent you from having to practice too much trimming.
  2. 2

    Gather your supplies. Go along all your basic tools in your workspace. If using power tools, make certain that yous have admission to power outlets. At the very to the lowest degree, you'll want a ruler, hammer, nails, wood glue or putty, and of course, your boards.

    • If using power tools, use caution and ever wear eye protection.
  3. 3

    Measure and mark your boards. First, you'll need to decide on the size of your box. Specifically, y'all'll desire to determine how long, broad, and alpine to make your box. Keep in mind you lot'll need to take grooves into business relationship and the fact that your lid volition demand to be narrower in order to slide into them. Then, mark the measurements on your boards using a ruler and pencil.

    • If you lot're building a box for a specific purpose or to hold a certain item, measure the item to ensure it will fit inside your finished box.[7]
  4. 4

    Cutting your boards, if not already to size. Use a hand or circular saw to cut the boards according to your measurements. Remember you'll need 4 boards for the sides, 1 for the base of operations, and one for your hat.

    • Ability tools can brand the chore easier, but are not necessary. You can hands brand your box using a screwdriver, carpenter's square, paw saw, and hammer.
  5. 5

    Cut grooves into the side boards. Use a table saw or router with a guide to cut a directly horizontal groove near what will be the summit and inside of the box. The groove should run near i/eight" deep along the height then your lid can slide into place. Make sure to cut equal grooves into three sides of your box.

  6. six

    Cut the front side of your box. First, accept 1 of the sides that y'all've already cut a groove into and measure from the top, where the lid will be, to the lesser of the groove you lot cut. Employ the same distance to cut a direct horizontal line beyond the top of your box front.

    • After this point, yous should be able to exam sliding the lid into the grooves and over the front if you lot clamp the sides together.
  7. 7

    Assemble the side pieces using a butt joint. Make certain the grooves are facing inward. Join the sides together at a right angle using glue between the joints for immovability. At this point, it should look like a square with no base of operations or lid attached all the same. Next, hammer or drill in finishing nails, wood screws or dowels.[8]

    • You may want to apply clamps to hold the glued sides together while you lot drill nails or screws into them.[9]
    • If you're using dowels, drill a pigsty through the side of i piece into the side of some other. Use a wooden dowel to pin the pieces together in an "L" shape. Later on the sides are pinned, cut the dowel flush with the sides.
  8. 8

    Secure the sides to the base. Make sure the sides sit evenly on the base of operations or are snug around the base, depending on your blueprint. Apply glue to attach the base and sides. Hammer or drill in finishing nails, forest screws, or dowels.

    • Permit your box to dry thoroughly before sealing or using information technology.
  9. 9

    Cutting the groove for the lid. If you want your lid to be affluent with the sides of the box, use a saw to cut a groove forth all the sides of the lid but the front. Slide the lid into the groves and over the top of the box.

    • For example, if your side grooves were cut ane/8" from the top and 1/viii" deep, you'll want to cut the top edges of your lid i/8" downward from the sides.
  10. 10

    Fill any nail holes. Utilize a wood putty and putty knife to fill boom holes. Let the putty dry out completely before sanding the areas smooth.

    • Filling and sanding nail holes will add a professional look to your project. Feel free to omit this pace if you're not concerned with decorative aspects.
  11. Advert

Add New Question

  • Question

    When measuring, don't you demand to include the thickness of the wood?

    Community Answer

    Aye. For instance, when using plywood, marker out the width of the wood before you attach the other side, and marking where you should put your nails, and how many depending on size.

  • Question

    Tin I use a hand saw?

    Community Answer

    Yes, just it volition take more than work with the hand saw. Also, precision cut will be very difficult.

  • Question

    What'due south the best measurements to use for making a wooden box?

    Community Answer

    It depends on how large y'all want it. The measurements I used were 9" ten 8". this was a good size for a trinket box, or a box to give a gift in, easily movable and looks nice.

  • Question

    How practice I build a wooden toy box?

    Community Answer

    Use the same method, but make information technology larger and used a hinged top.

  • Question

    What kind of wood should I use? Should I use softwood or hardwood?

    Community Answer

    Hard plywood volition last much longer and hold its shape and remain stable improve than softwood. Hardwood looks cleaner than softwood but it merely depends on the purpose of the box.

Inquire a Question

200 characters left

Include your email address to get a bulletin when this question is answered.

Submit

Advertizement

Video

Thanks for submitting a tip for review!

Things You'll Need

  • Carpenter's square
  • Hammer
  • Hand saw
  • Nail punch (optional)
  • Circular saw (optional)
  • Electric drill (optional)
  • Woods of your choice
  • Gum
  • Fasteners (dowel rods, wood screws, or finishing nails)
  • Hinges

Nearly This Article

Article Summary X

Before making a wooden box, choose some wood and gather your tools, including a hammer, nails, forest glue, and a saw. Then, measure out your boards according to the size of the box you're making, mark them, and cutting them to size using the saw. Next, assemble the side pieces using wood glue and reinforce the sides with finishing nails. Attach the base of operations in the aforementioned manner, and then attach a hinged lid with the swivel facing out. To finish, fill up whatever nail holes with putty, let information technology dry, and sand it polish. If you want to larn how to make a box that has a sliding lid, keep reading the article!

Did this summary help you?

Thanks to all authors for creating a page that has been read 533,813 times.

Did this commodity aid you?

knightwhimints.blogspot.com

Source: https://www.wikihow.com/Make-a-Wooden-Box

0 Response to "Wooden Box With Drawer Plans"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel